TRENDnet Punch Down Tool With 110 And Krone Blade, Insert & Cut Terminations In One Operation, Precision Blades Are Interchangeable & Reversible, Network Punch Tool, Grey, TC-PDT

My Microsoft Surface notebook is a great computer except for having very slow Wi-Fi speeds. All other computer devices in the house obtain a little over 400 MBPS Wi-Fi down link speed. The Surface only obtains, at best, a little over 100 MBPS. A CAT-5 Ethernet cable wall outlet was on the opposite side of my office room computer desk. The cable connects to a Spectrum router in an adjoining room. The cable was re-routed in the walls to behind my desk. A flat stick punch tool, for telephone wire connecting, was used for terminating the CAT-5 cable ends on Keystone wall plates on both ends. The Internet download speed was still just a little above 100 MBPS. The TRENDnet Punch Down Tool was used to re-punch down the 8 wires on each Keystone receptacle. The Internet speed leaped to as high as 690 MBPS. The subscription from an Internet service cable provider is 500 MBPS down & 20 MBPS up. The TRENDtool was very easy to use with great results, a very beneficial investment!

Working as a network tech I have used most brands of punch down tools out there. The best brand for any network tools is typically Fluke....except their punch down tool. I have had nothing but issues with their tool and this punch down from Trendnet is PERFECT!Build Quality - I have used this for approximately 200 installs which would mean ~10000 terminations. I have had ZERO issues with this. I sharpened the blade around install 150 as it was getting a little dull and harder to punch. It is still working perfectly to this dayAdjustments - I typically don't use any of the adjustments and keep it at a standard impact. The adjustments do work well from what i have tested.Cost - So much cheaper than Fluke it is insane. I don't know why you would go with any other brand.Warranty/Support - I haven't had any issues yet so I haven't contacted their support5/5 - I am a huge fan of this product and I hope this review helped!

I recently purchased this to replace my sons last punch tool which was stolen from a job site. he is an IT pro and use this once in a while. I dont do cabling full time but I do need to punch a jack now and then or replace a bad cable. THIS IS NOT A HIGH END TOOL like a fluke but does the job well. always punch twice with medium pressure set and it cuts the wire every time and produces a solid connection. The only down side is they included a krone blade which is not used in the USA so it is useless. They should have included a 66 blade which is used for telephone work. I will be buying another one as a backup and fitting it with a 66 blade.

I normally use a Harris (now Fluke) D-814 that I've had and enjoyed for over 2 decades, so my review is based on experience with the higher end tool. I sometimes need a second punch down tool or don't have the Harris/Fluke with me, so I thought I'd try the TRENDnet.Side by side with the Harris/Fluke, it is obvious that TRENDnet copied the Fluke time-tested design very closely. The plastic is lighter and has a less substantial feel to it. The knobs/wheels are hollow instead of solid. The springs for the impact adjustment and blade storage are not as tight as the Harris/Fluke tool. The body of the tool is slightly larger and more squared off at the edges so may not be quite as comfortable if using it for an extended period. Despite these differences which I'm sure is how the lower price point is achieved, the tool is solid and works well. If I did not have the Harris/Fluke to compare it to, I'm sure I'd be thrilled with this unit and I probably would have given it 5 stars.The blades interchange perfectly with the Fluke blades and tool. The 110 blade has a slightly different profile than the Fluke blades that I have, but it works well regardless. The cutting blade is thicker towards the tip and thinner away from it, so it may not last as long.When all is said and done, I think this is a great punch down tool for the price. If I was looking for a primary tool to be used every day in a professional environment, I'd lean towards the Fluke. I don't know if this will last 20+ years like my Harris/Fluke, but for less frequent use or if you expect to lose it, loan it and never get it back, etc. I'd say this can't be beat for about 1/3 of the price of the Fluke.I don't know how to caption the photos, so I will describe them here:Th first photo is the TRENDnet tool and blades. The 110 blade is installed, and the Krone blade is in front. Also shown are the blade covers, which are a nice touch.The photo of the three blades shows a Fluke 110 blade in the foreground, the TRENDnet 110 blade in the middle, and a Fluke Eversharp blade (silver) towards the back.The photo of the two blades has a Fluke 110 on the left and the TRENDnet 110 on the right. They are nose-to-nose so you can see the difference in profiles.In the group of photos showing two tools, the TRENDnet is on the top or right, and my old Harris (now Fluke) D-814 is the yellow and blue tool on the bottom/left.

I purchased this tool because I needed a simple punch down tool and my local Home Depot and Lowes carried punch down tools for double the price. It does what it is supposed to do. Sure it doesn't always cut the wire completely when you punch down, but you just punch again, wiggle if you need to and you're good to go. Would I buy this if I needed this everyday for my job? Ehh, I'm sure there are better ones out there. But for wiring up my basement and other small, odd jobs, this is perfect. I've used this on Monoprice's slim cat5e punch down keystone jacks and ICC's data modules. It worked much better on ICC's data modules, but only because they were installed in a low voltage cabinet. The cat5e jacks I was holding in my hand. In that situation it's still very usable, just more of a pain, but that isn't the tool's fault. The impact selector is nice, but to be honest, I just keep it on the HI setting all the time.

Bought Years Ago - Still Works! If you are new, just getting into the field ... Just buy it for those short time on site / punch down backboards. Or the tight spaces ... quick low pay jobs ... that you just want to get in and out quick without spending a lot of money. Get your experience and move on. Yes, the tool works.