NETGEAR Wireless Desktop Access Point (WAC104) - WiFi 5 Dual-Band AC1200 Speed | 3 x 1G Ethernet Ports | Up to 64 Devices | WPA2 Security | Desktop | MU-MIMO | Supports 3 SSIDs | 802.11ac

Once you get it set up, it works fantastic. Strong wireless signal on both 2.4 and 5 bands. Super-fast wireless from my 900MB home broadband. Excellent access point.The only thing is, as others have said, is that the instructions for how to "just plug it in to a port on the router, and DHCP will take over, and then set it up" are unproductive. The default setup in the AP is for DHCP, but for the wrong network due to its default IP address of 192,.168.0.100. My router is 192.168.1.1, and the AP doesn't get set up properly by DHCP. I tried to follow these instructions first, and as others have said it just doesn't succeed, for the obvious reasons.But I've had prior experience with an earlier version of the Netgear access points, model WN604. The setup approach in that older model was outright described for manual method, temporarily connecting directly to a laptop or PC via ethernet cable. These are exactly the same manual configuration instructions as are described in the user manual for this new WAC104. Once you take this manual approach, instead of the DHCP approach, it's just a few minutes to complete the setup and get the WAC104 prepared for actually being connected on my 192.168.1.1 network.You first need to get your laptop or PC into the TCP/IPv4 properties, in order to change from "DHCP" to "manual static IP" mode. This is from Network and Sharing Center, and then click on "Change adapter settings", and then select your ethernet connection object, and right-click and select Properties to get the Properties dialog window. Then select the "Internet Protocol Version 4 (TCP/IPv4)" item, and push the PROPERTIES button. You're probably in "obtain an IP address automatically" mode, which means your PC/laptop is normally handled by DHCP from your router. Temporarily you must instead change this to "Use the following IP address", to assign a static IP (as described in the manual setup instructions of the WAC104 user guide) that will make the WAC104 directly visible to your PC/laptop.Enter an IP address of say 192.168.0.201, and a subnet mask of 255.255.255.0, and you can leave the "default gateway" blank. Then push OK, and OK your way all the way back out, and shut down. Then disconnect the ethernet cable from your PC/laptop to your LAN, and instead connect it from the PC/laptop directly to one port of the WAC104. Now re-boot the PC/laptop, and ignore any startup errors you might get from any of your software that might complain about not being able to get to the internet.On the computer, open a web browser and enter 192.168.0.100 in the address bar. A login window opens.Enter the access point user name and password.The default user name is admin. The default password is password. The user name and password arecase-sensitive. You can change these default values later as part of your setup, if you want.The Home page displays.Customize the access point settings for your network environment. My approach was to configure the WAC104 for "static IP" (not DHCP), exactly as I did with my previous WN604. I picked a known available and currently unused IP address of 192.168.1.124, with a subnet mask of 255.255.255.0, and a default gateway of 192.168.1.1, and a primary DNS server of 192.168.1.1. This means in normal operation your WAC104 will always have a static IP address of 192.168.1.124 from your router at 192.168.1.1. And that means you can always subsequently get back into the setup dialog of the WAC104 if you want to, by using a browser and addressing it via 192.168.1.124.I also set my desired new SSID network names for the 2.4 and 5 networks, along with the new passwords (i.e. "passphrase") for those WiFi network signins.I also set wireless security to "WPA2-PSK [AES]", for maximum wireless speed on both 2.4/5 bands. At first I checked "WPA-PSK [TKIP] + WPA2-PSK [AES]" but when I pushed APPLY I was warned about the full-speed limitation of this option, something I wasn't aware of. So I instead checked the "WPA2-PSK [AES]" option which is perfectly fine with me.If you want you can also change the WAC104 login username and password through the Administration -> Set password dialog.Push the APPLY button, to save all customized settings.After you complete the setup go back into Network and Sharing Center, etc., and change the PC/laptop TCPIPv4 properties back to original IP address or DHCP. Then shut down the computer and power-off the WAC104, and disconnect everything.Now you can reconnect the PC/laptop with ethernet cable back to your router, and reboot. Everything should be back to normal again.And you can connect the WAC104 through its own ethernet cable run to an open port on your router (or remote switch). Power-on the WAC104, and wait for the lights to stabilize. You should now be able to confirm that you see the two new 2.4/5 WiFi networks using your smart phone and a WiFi Analyzer app.You should also confirm from your PC/laptop that you can also get to 192.168.1.124 via a browser.Simple and straightforward. Just manually connect static-IP PC/laptop via ethernet cable directly to the WAC104 for setup.

This works as a Wireless Access Point (WAP) with hardware passthrough, and it works just as that! It has default SSID name and password, as noted on the bottom of the WAP.As others have said, it is difficult to setup if you're unfamiliar with this kind of tech. The instructions expect your router to allow for static IP, but they're traditionally dynamic so the URL they give you won't take you to the "admin" page. Which forces you to try and find the IP that the router has given this WAP.On mac, I opened the command line and ran `arp -a` to list out all the IPs connected to the router, which might be a lot for you, I had about 20 devices. This command will work from the windows command line (cmd).In order to find the WAP IP, I then went through each IP and entered it in the browser (e.g. http://192.168.0.[0-255] - again I only had about 20 options) until I was prompted for a username/password (you might find your router's admin page, which is not the same, usually 192.168.0.1 or similar), NETGEAR's admin page launches with a browser popup. From there I was immediately asked to rename the admin password. Then I updated the 2.4 and 5ghz SSIDs and passwords.I'll be buying another

I bought this access point for use in my home. The way my house is set up, the internet comes in to the downstairs, into a corner of the house. The house is older and everything is finished, so it's not the easiest thing to put our wireless router anywhere that gives coverage to the entire house. Because of this, my bedroom is a Wi-Fi dead zone. I do have a Cat5e cable run to the upstairs and connected to a switch, which provides network connection to our entertainment center. I have placed this access point on the entertainment center, and it provides good reception to our bedroom on the other side of our 1500 square foot house. Once I was able to access the setup menu, things were simple and I was able to configure the access point to my liking.Setup, however, was a bit tricky. First off, I'm not a network professional, but I do consider myself above average in networking knowledge. I have a small home network with a NAS box, a desktop PC, two laptops, a smart TV, networked sound bar, Xbox one, Chromecast, a couple tablets and a couple of phones connected to it off and on. I've been able to set up all these devices myself with little difficulty. After unboxing this access point, I connected it like the instructions directed, and then I opened my browser on my desktop PC (which I had plugged directly into the access point) and directed it to the device's default network address, 192.168.0.100. Unfortunately, my browser couldn't find anything there. I still had internet access and I was able to use the access point as set up out of the box to access the internet with my phone wirelessly, too. I knew the access point was working, I just couldn't get to the setup page. It turns out that my router (an ASUS RT-AC68U) has a default address of 192.168.1.1. Since the access point's address is 192.168.0.x, I was unable to see it with my computer's IP address settings. To fix this, I had to manually change my PC's IP address to 192.168.0.200, and then log into the access point at it's default address of 192.168.0.100. Once in, I changed the access point's IP address to 192.168.1.202 (outside of my DHCP client range on my router) and set the default gateway to 192.168.1.1. Then I reset my PC's IP address to the way it originally was, and was able to continue normally. All this setup was because my ASUS router and my Netgear access point have different IP addresses. I don't blame Netgear for this, as I bet if I had a Netgear router, it would have worked without a hitch (at least I would hope it would).As I said above, the access point worked out of the box and gave my devices network access, but I wanted to get into the settings. Why not just leave everything the way it came? Because the way it came, the wireless was set up with no security whatsoever. Completely open to anyone in the world to get into your private network. The back page of the setup guide says that the access point automatically uses network security, so you don't need to set it up. Unless you want to give your neighbors open access to your network and free internet, I would disagree with this statement. If I understand correctly, this device hasn't been out long, and I bet this is something they will fix in the future, but at this point, I wouldn't buy this for my grandpa, or anyone else who doesn't know technology very well.As for the device itself, it's a little bigger than it seems like it needs to be, and it has a bit of a hollow feel to it, like it's got a lot of open space inside it. The antennae do seem sturdy though, and the range is good. It's also got two mounting holes on the bottom, so it can be wall mounted, if needed. There are also four gigabit ports on the back, which allows it to be used as a switch (for up to three additional devices) in addition to the wireless access point, which is nice. The configuration page, once accessed, is pretty standard stuff; I was able to assign unique names and passwords to both the 2.4 and 5ghz bands, as well as change other settings as I would expect to.I gave this 4 stars from my perspective, as once it's set up, it works just like I feel like it should. One star was removed because of the open security, which seems like an error, and the setup difficulties were neutral, as I don't really know of a way around this when the default addresses are different, based on my somewhat limited knowledge of networking.Bottom line: This is a good buy if you need a separate wireless access point and you have a Netgear router, or you aren't afraid to work a bit of googling things to get the set up complete. I would maybe look elsewhere if your router's brand is not Netgear and you are a bit scared of figuring things out.