Genie Chain Drive 550 Garage Door Opener, Heavy Duty Chain Drive Opener, Model 2035-TKO

I purchased this garage door opener to replace a Stanley model from the 1990's which cracked the drive gear housing. Rather than buy the replacement part for $40 plus shipping, I chose to replace the whole unit and I am very glad I did. The install was fairly straightforward since I was replacing an existing system and the wiring was all compatible.First impression: The system is dainty and quiet. I would say the Genie motor housing is half as big as my old opener but my old opener was a big empty box of old tech so that makes sense.Keypad remote is a nice extra and straightforward to program. Took me two tries as I think it didn't register one of the digits in my pin so I had to reset it and start over which the instructions also covered.Install hiccups: (1) You are supposed to tension the chain until there is a 1/4" gap between the chain and the bottom of the rail. I couldn't get anywhere close to this tension without it binding hard so I chose to let it sag a bit lower. (2) The instructions are very accurate and actually pretty amazing and should be applauded. At one point, the instructions direct the user to carry out three steps to connect the chain bar to the motor housing but the first two are for chain drive and the latter is for belt drive. Not even close to a real issue but worthy of an edit in my opinion. (3) You are hereby warned to wear disposable gloves. The bar is absolutely covered in lubricant as is, of course, the chain. Again, you've been warned.So far: I can't stress how much quieter this unit is than my old opener. Sitting on a deck above the garage, we cannot hear it unless we listen for it (garage roof is concrete). No, it is not silent, but it is miles less obnoxious than old models of openers.Warranty: my remotes came scuffed and cut up. Genie was very responsive through their online chat support (phone support has unreasonably long wait times.) It seems that the metal visor clip which ships detached from the car remotes can get in front of the remote and slice into the plastic. Not a deal breaker but after spending a long time installing the opener and the keypad, the car remotes were the last thing I opened so ... oof.In all, I would highly recommend this opener.

The Genie Chain Drive 550 (Model 2035-TKO) works exactly as expected. It’s reliable, sturdy, and opens and closes the garage door smoothly every time. The included instructions are decent, but I’d recommend checking out some YouTube videos as well—there are some really helpful step-by-step guides that make installation even easier. Overall, great value for the price and does the job well!

This is exactly what was expected from an inexpensive opener. I unpacked it and checked the contents to the parts list to insure everything was there. It was fairly easy to follow the instructions for the basic installation. I took one additional trip to the store for a needed piece of 2x4 to provide a good place to secure the motor unit. Working alone, the installation and basic set up took about 4 hours.I did have a problem (probably my fault) figuring out the written instructions on how to program the wireless keypad, and the universal remote in my Chevrolet Blazer. A call to customer service had a long expected waiting time, but they called back after 30 minutes. The representative then quickly walked me though the correct set up procedure in order to get both things working successfully.The overall quality of the opener itself seems good, but I would consider the keypad and accessories a bit on the flimsy side, especially compared to the components of my old Craftsman 3/4 HP opener. I suppose it's a sign of the times and the manufacturer's cost cutting efforts. I guess time will tell on how durable they really are.

This opener replaced my craftsman that was approx 24 years old.This genie was pretty easy to install. I thought the directions were good.This is waaayy quieter than my old one.The one thing that was troublesome was the program and control buttons on the opener. One of the final steps was to program the down limit and up limit. The buttons on the opener are molded plastic that are molded into the bottom plastic cover and they should push the buttons on the circuit board underneath. These plastic buttons either did not line up or were not in the exact right locations because when I pushed the up button, it did nothing.I was able to remove the plastic cover and push the buttons on the circuit board in order to program it and that worked well so it is just a flaw in the plastic cover that was causing the problem. I don't forsee needing to reprogram these limits so, hopefully, I shouldn't have to remove the cover again.

easy to install. very quiet, Satisfied.

Nice product and very quiet compared to my old craftman, I had to replace the whole system but the kit contained everything you needed. Took about 4 hours.