RealTruckBAK BAKFlip MX4 Hard Folding Truck Bed Tonneau Cover | 448130 | Fits 2019-2025 Chevy/GMC Silverado/Sierra, w/MultiPro/Flex Tailgate (Will not fit Carbon Pro Bed) 5' 10" Bed (69.9")

Looks great, and easy to install. Just be sure to watch the videos on how to install.I really like that you can still see the top brake light even when the top is folded all the way up.

First, I spent a fair amount of time doing research for a decent tonneau cover. When I purchased my truck, I knew I needed a tonneau cover. I initially was leaning toward a retractable-style cover for a couple of reasons. One - I wanted something that would make my bed both secure and dry. Two - I wanted something that would be out of the way when I needed the full bed and was electric actuated. Third - I was fairly certain I wanted something constructed of metal rather than plastic or vinyl. There was one issue with electric retractable tops is they are VERY expensive! So, eventually I had arrived at the conclusion I just didn't want to spend the money for a retractable top, but wanted the sturdiness of a metal retractable top. BakFlip hits 2 of my 3 asks for a tonneau cover - AND at a fraction of the cost! So, this is MY comparison contrast between retractable vs folding tonneau covers.Next, when it arrived, it was packed very securely. I was a bit worried after I had ordered because I had read some reviews that indicated their cover was damaged during shipping. The box was large and bulky, but wasn't unmanageable. My 17 year old daughter actually got it into the house just fine on her own.Installation. My advice on installation is to unwrap the cover and brackets and separate the hardware into piles (nuts, washers, lock washers). The other reviews on here are spot-on! If you are like me and you're a garage 'tinkerer' with cars and trucks and know your way around a toolbox, you will have no problem with the install. It took me about an hour. Just be sure, to pay attention to the alignment and insure the brackets are grabbing your bed rails squarely. Definitely worth going back around to give the bolts a final 'snug' when you're done.Performance. I saw mixed reviews on here that were indicative of the cover leaking. The cover (so far) has kept the gear in my bed dry during the handful of rainstorms we've had since the install. As for the dust? Here's the thing. When you put one of these covers on, you are sealing around the top of your bed. The penetrations and voids UNDER that cover will allow dust (and in most cases water). How is it the tonneau cover's fault? Get creative if you want your bed to be air-tight.Overall, I am pleased with this purchase. In the end I am happy that I decided to save about $1600 because, as it turns out, I don't think having a remote and being able to click a button to retract the cover is worth an extra $1600. I hope this review helps if you are on the fence like I was...

Impressed with the design on this. Its low profile, fairly easy to install. Make the truck look good.I gave it 4 out of 5 on installation due to i needed another body to help hold a corner down to have it sit right for bolt down. Even that, wasnt difficult at all. RTFM and golden.I tested it thru many a carwash (Crew Carwash) which has high pressure. Hardly any water gets in. Little by the tailgate.We'll see how it holds to sun damage/coloration and the weather. I personally think it will do well!Foldup: This is a must if you use the bed for hauling things. This top folds ups nice and easy. Simple pull down on the cable and flip it over!The mfg states it can hold up some weight. I'm not going to try it unless I have to. I trust what they say. Its a solid top.If you are thinking on this one, dont hesitate!

Great cover! Did a lot of research before I landed with the BAKFlip Mx4. Super easy to install, very secure, I’d say more secure than the other ones with the latches. You can also have up to 400lbs of evenly distributed weight on top. Yes pricey but the invest for security made the decision easier

I've owned 2 Backflips and a couple of other brands as well. After finding Backflip, I never went back. Although I find that this cover does not seal to the bed quite as well as some others I've tried, it's a minor trade-off for getting a lighter, sleeker, more convenient and less bulky cover. It's not completely watertight, but that's not a big issue for me because it still blocks most precipitation and drains it from the cover. What little water does get in the edges is not enough to get anything inside wet, as it just trickles down the grooves in the bed until it drains out. I've been camping, skiing and hunting in the rain and snow and none of my gear has ever gotten wet. The only improvement I would suggest is another clip receiver in the center of the cover so that you can fold the first section back and clip it. Often, I have something like a grill or propane tank or piece of equipment that I tie down in the back. There is no way to safely just fold back 1 panel and lock it down. You have to fold it all the way back, which exposes the rest of the bed to the elements and wind. Minor issue though. Oh BTW, their customer service is great.

Had some initial issues but the seller and manufacturer helped me work it out very quickly. Now that it's all complete and properly installed... I love this thing!Super durable and lightweight. Can lift it from the side with one hand easily. Has options to ride with it opened if needed which is nice. Have had no issues with water or leaking either.Installation on my 2021 GMC Sierra Elevation was easy and took about an hour to complete. It took me longer to get it square on the bed than anything else.

Don't waste your time. Installed on a GMC Sierra AT4X. I have installed several covers and usually this is a good brand but this was junk! The rails went on fine and I always expect some adjustment of brackets to get the fit just right but this took me forever to get the driver side to latch properly. I did finally get it to latch but as I was doing a few open and close test I dropped down the last panel and the corner piece of plastic broke off. I am sure they would replace it but why have such a weak point at the corner like that. I am also not a fan of how the back fits over the tail gate, maybe mine specifically just had weirdly bent rubber that would smooth out over time but as it closed the first few times it was far from water tight. I have usually had good luck with Bakflip but for this truck I am looking elsewhere.