Upgraded 3D Printer Extruder Level Gear and Idler Arm with Groove for Titan Aero Prusa i3 Ultimate Artillery Hornet Sidewinder X1 X2 Genius/Pro Extruder Parts (Black)

This is a good replacement set for a real Titan. However! These gears and lever work with the genetic Titan but will require and additional item and a little work. I have replaced entire China titans more times that I can mention but reason it usually due to worn arm or worn feed gear as after a few hundred hours the gear teeth get worn down. You can file them to get a little more bite but this gear set is the answer. You WILL need 5mmx10mmx3mm bearings to make this work as the shafts on this gear are smaller than the china ones. There is no 5mmx10mmx3mm bearings. So your choice is 5mmx9mmx3mm these will fit this gear perfect but not the hole in the china plastic frame. They are 1mm to small so your gear will wobble. It WILL work if your tighten the thumb screw for tension really tight. Or if you find or print a 1mm shim. Or you can go with 5mmx10mmx4. This best choice. As it fits the hole and the shaft perfect but sits out about .5mm to far I used a solder iron to heat bearing and push it further into the plastic or you could remove some of the plastic to make it work. Now for about 15$ you have real hardened Titan gear metal arm and better bearings in your genetic Titan. I highly recommend the metal arm and the hobbled gear. This is good quality set. I’m buying 5 more.

I got what I ordered, and it fits my machine as advertised.

I went from a pattern of gaps in my prints to solid, even lines. I didn't realize my extruder gear had worn down on my Tronxy XY-2 Pro Titan. Be mindful that the Idler Arm does not fit the Titan extruder that comes with the one from Tronxy. But this is a turnkey solution for folks who are getting under-extrusion but have checked everything else (bed, hotend, teflon tube, nozzle).

This trash can't be bought. I bought it and ended up buying a new motor.

Sidewinder extruder level broke. Ordered this unit to replace. Works great.

The lever gets hot and the filament gets stocked because is melted in the gear.

Muy buen prpducto

I HAVE 12 ARTILLERY SIDEWINDER X1s I PURCHASED 4 OF THESE ITEMS TO SEE HOW WELL THEY WOULD PERFORM OVER THE STOCK PART....AFTER 100 HRS OF PRINT TIME ON EACH UNIT THEY STARTED TO FAIL DRASTICALLY!! THE NURLALING THAT ENGAGES AND BITES INTO THE FILAMENT ON THE MAIN DRIVE WHEEL LOST ITS SHARPNESS COMPLETELY AND WILL NOT BITE INTO THE FILAMENT AT ALL REGARDLESS OF THE TENSION. NOT ONLY THAT THERE ARE SOME OTHER ISSUES WITH THIS PRODUCT I DON'T EVEN WANT TO SPEND ANYMORE OF MY TIME EXPLAINING.THE STOCK PART OUT PERFORMS THIS PRODUCT SIGNIFICANTLY............DONT WASTE YOUR TIME OR MONEY!!!!!!!!!!!!!!!!! I WOULD LIKE A REFUND BUT THE COMPANY IS NON RESPONSIVE AND I AM PAST THE 30 DAY RETURN-REFUND PERIOD.

Muy buen producto y excelente calidad

Idler bearing fell apart after a few prints and jammed, complete junk. Arm itself is of good quality, but idler won't idle after bearing jammed and therefore printer can't extrude filament.

Réparation de ma Sidewinder X1, parfait, prévoir les roulements en plus.

Sono molto soddisfatto. La stampante finalmente ha un buon mordente al filo della bobina, cosa importantissima per non aver problemi di stampa. Purtroppo l'originale, in plastica, prima o poi inevitabilmente si mangia....Piccola nota e consiglio, ho riciclato ed usato la molla originale che fà fare più presa in quanto è appena più lunga.

Rugged and sturdy. No problem to install. Way better than the plastic oneI highly recommend this if you want more even extrusion