Anycubic Kobra 2 Max 3D Printer, Max 500mm/s High-Speed Printing Large 88L Printing Volume with Auto Leveling Smart Z-Offset Vibration Compensation Enhanced Print Quality & Detail 420x420x500mm

The media could not be loaded. It is a product that perfectly meets the specifications stated by the manufacturer. It is easy to assemble and comes with some extra accessories. There are several videos available if you encounter any problems, and the technical support from Anycubic and Amazon is very effective. Plus, it's aesthetically pleasing.It has good print quality, and its calibration was very easy, so if you are a beginner, it won't be difficult. Its interface was very straightforward, and I used Cura for slicing. It had good bed adhesion, its replacement parts are affordable, it has a very large bed, and it reaches a good height. It is a bit noisy when printing quickly and can move everything around it, but it is mesmerizing to watch it print so fast.After a while, I had a technical problem that I tried to resolve. Anycubic was very attentive in helping me, but there was no solution, so they asked me to return it and gave me a refund. But I miss it.

When it works, it's great. I appreciate the large format capabilities, and the prints that actually completed turned out pretty good (after the expected tuning).Unfortunately, there have been quite a few problems with this printer. Out of the box, the axis sensors had poor quality connectors. I had to splice a new connector into the Y axis right out of the gate. X axis limit switch worked intermittently as well but seems to have resolved itself. Very very very cheap and poor quality components.I have had this for about 3 weeks and already needed to replace the thermistor in the hot end (tbh it was easier just to buy a whole new head, luckly cheap). But the worst is now the bed doesn't stay at temp as soon as printing starts. It will heat/preheat fine then just shut off. No GCode or slicer issues (previously succesfful prints now fail), and clearly the heater element is working. Ambient temps are about 20*C and no drafts, no fan usage (PETG @255/80).So -- you get what you pay for. Seems like many folks on here have been lucky but I've had more downtime than uptime with multiple independent failures. Being cheap, at least its been cheap to repair but can't say it has been convenient or positive.

High precision and fast prints with excellent output quality. ( I use either a .8 or 1mm nozzle, not a weenie .4, for all my work and the extruder handles it effortlessly. ) The bed surface is a joy, holds the print in place well and releases it easily when cooled.My only criticisms regard minor firmware issues; for instance, if one decides to disable the part cooling fan temporarily during a print, they will discover that it will not turn back on later in the print.Also there is no way to incrementally increase or decrease printing speed slightly , one is stuck with 'Stable', 'Standard', or 'Sport' modes. This means one spends a lot of time dialing things in with the slicer/repeatedly loading the print file for every slight change in speed, a real pain in the butt. As all makers know, with a wide range of filaments and model parameters to work with, getting the exact perfect print speed can be a chore, and an incremental speed adjustment feature would save a lot of time.Another quibble is that Every time I shut the machine off and start it again later, the bed z calibration settings seem to vanish, requiring a bed level run on every startup, which consumes a lot of time.On the plus side, the motion-correction software seems to work quite well; the table I have the printer on shimmy's a bit but this does not affect the print quality.The pictures show my first project on the printer, a 420 hour print of 2 custom designed speaker enclosures in matte black PLA, along with a SPL graph of the finished result. They are double-walled with fine quartz sand between the walls.

​ **Assembly**Got this a few days ago. Assembly was smooth, but check the (short) video on YouTube, rather than rely solely on the booklet.The video of the assembly makes it much more clear, but overall, no issues.​ **Hang Issue (Firmware!)**After a simple benchy, the first print STOPPED MID PRINT, with the fan still blowing, and screen blank and unresponsive. This happened on the second try, and kept happening on various prints. LAME!However, the interwebs eventually solved the issue for me, and others here have said it as well:!!! You must UPDATE THE FIRMWARE for the printer to work !!!This is super easy, you just connect to Wi-Fi, go to the firmware (v2 something by default), and update to the latest (v3, which fixes everything).You need to run the PID calibration / (for the "stability" vibration compensation setting) after the update.​ **Slow. It. DOWN.**The printer has onboard vibration compensation (PID), but you have to turn it on after each print. (Start print, then set time to "stable.") It's lame and odd that this cannot be enabled by default, because it's sort of an essential feature ... prints will be somewhat slower than the official time in the gcode, but will look way nicer, and be less likely to fail.Also, the slicer settings are absurdly TURBO by default. I turned everything down in the machine limits part of the slicer, and cut all the values (velocity, jerk, acceleration) in half. I call this the "gentle" setting, for naming, and use this as my default printer setting.With stability and "gentle," the printer just feels nice and peaceful and chill while printing. I was having a hard time to get prints to complete, on the default "berserk" setting.It still sounds like a wind tunnel, though. The fans are annoying, and probably not necessary to be that loud. The printer itself (motors, etc.) is pretty quiet.​ **Get It Sliced Right**The default slicer is the AnyCubic slicer, which is a fork of the PrusaSlicer. The project files are identical, you can read and write them with either program.I actually like the AnyCubic slicer a little better, it looks nicer (and of course has the printer in there, by default.)I did need to tweak the settings. Some things that worked for me:* 3 perimeters, rather than 2, is much stronger and looks better* Gyroid at low density (10 - 20%) is a great infill. The curves make it strong, and it looks awesome (especially in clear)* Hilbert curves for surfaces look nice* No skirt or brim* I turn OFF "Detecting Bridging Perimeters" ... it causes more problems than it solves. For instance, if you have a small screw screw hole, it will close off the top "bridge" even if the hole would have printed just fine.* Stagger inner seams (for strength and printability), and set the outer seam to "rear" (looks best, of the options)​ **Upgradable Nozzle + Carbon Fiber**When the printer first came out, it took a few months for nozzles to appear, since anycubic reengineered their nozzles for the Kobra 2 series. You can get nice ones now, I upgraded to a ruby 0.6 mm nozzle from durozzle (available Amazon for 25 bucks).Ruby is 9 on the hardness scale, basically right behind diamond, which is 10.Ruby (or diamond) lets you print abrasive material, and I have discovered carbon-fiber embedded PLA. It's just a whole new world. Prints are strong, to do not warp or shrink, and feel and look nice.In addition to the hardened nozzle, to print CF you need to keep the filament in a dryer ... I have not figured out a placement that allows the filament to flow freely to the printer, without taking up massive space. (I just set the filament a few feet away, so no sharp bends.) But still, it's awesome and worth it, and I have no real plans to print anything else ...For the nozzle, I had to change only three settings:* nozzle diameter to 0.6 mm (duh)* linewidth to 0.67 mm* and layer to 0.3 mm.That was it, I kept the previous "gentle" speeds.​ **IT'S ALIVE**The printer is awesome. BUT Anycubic deserves minus one star, for sure, for shipping a broken printer (bad firmware). Printers are difficult enough, and although I eventually found the solution, I went down the rabbit hole of thinking it was overheating (?) or browning out (?).People ask this question on line (was very common on the Vyper), and many of the threads end in "it's still not working" ... why does AnyCubic not post the solution?(I have a friend with a Vyper, that stopped working in the same way ... I did not know about it when I got my printer. The hang issue is VERY COMMON, but somewhat sporadic, and really hard to debug.)​ **Conclusion**This printer took a LOT more effort to bring up than I was expecting. Along with the firmware issue, "stable" should be on by default.The default slicer settings are meant to sell the printer on SPEED, which is good because it means the printer is solid, but need to be slowed down to something reasonable, to actually have nice prints.BUT the end result is really cool, for $500 plus a little more for accessories (hardened nozzle, and filament dryer).At some point, I'll see if there is a way to make it less loud (the fans could at least be turned down), which is my one remaining gripe.Overall, solid, would recommend.