OVERTUREPLA Matte 3D Printer Filament 1.75mm, Matte PLA 1kg Cardboard Spool (2.2lbs), Dimensional Accuracy +/- 0.02 mm (Matte Rainbow)

Just WOW!. I'll update with photos of my prints later on. I've been searching for matte filaments and there seems to be limited options. Not only have i think i found it, i dear say i found my goldilocks filament. Ordering 3 more rolls next week as I've been printing 24hrs a day since i got it a few days ago. Excited to try other colors. Roll was nicely wound and print quality is astounding, printing is very easily and was dialed very quickly. and i have zero complaints so far. Layer lines are pretty much invisible even at .2 layer heights. .13 is jaw dropping.Been printing an order for a local hobby shop and they at first didn't believe it was 3d printed as it looked multitudes better than previous filament I've used on their order. I've been printing on my mostly stock ender 3 v2. Only modifications are z-brace rods, bltouch, dual z and printed z motor mounts. Printing here the update NY winter is usually challenging as where i print in my home can be as low as 10c ( will be finishing my enclosure soon). Saying that my only struggle has been minor corner warping and bed adhesion. but i doubt that would be an issue in warmer rooms. The issue has been resolved though as i really squish my first layer (leaves very fine elephant foot that cleans quite easily with a sharp hobby knife or 220grit sand paper) since i print 7-20 parts at a time. Can't afford failures. I am printing on the stock textured side of the ender 3 glass bed.For those with an ender 3 i do Hot end at 195-200c, 60c bed temp at 40mm sec (as i prefer quality over speed ) retract 6.5mm 50mmsec, default cura coasting settings and filament equalizer enabled. 75%-100% fan after initial 2 layers.I'd also like to add that my printed upgrades are done in hatchbox abs for strength and temperature resistance. But now any parts that aren't at risk of high temperature exposure I'm using this matte black pla because it looks that amazing and is suitably strong.If I run into any issues I'll update accordingly.Update 7 Days LaterSo i ordered this filament for an order for a hobby shop. Printing drag racing slot car stands. I printed 96 of these in 4 different filaments. After the first 28 this filament arrived and after the first test prints i was amazed and now only use this filament. I went through the whole 1kg roll in 6 days. Ordered another and already been printing into the 2nd roll. I've updated my nozzle temp to 210c and I'm using a .8 brass nozzle. A worth while mention is these stands i print they're only 3 bottom 2 top, 1 perimeter and 0% infill. And they're almost perfect, very light and just as strong as previous prints with .4 using 3b 4t and 2 perimeter. The watering can is from thingiverse and printed at 60mmsec, 3 bottom and in vase mode. Also worth noting i check filament diameter periodically as i go through the roll and so far it's been between 1.72-1.77mm.Overall still my new favorite go to pla. I definitely prefer a matte finish and this filament definitely delivers.

I don't often write reviews, but this filament is top notch. Running it on a Bambu X1-C through the AMS, using a 0.4mm nozzle. No clogs at all so far. Some others have mentioned clogs with anything less than a 0.6mm nozzle though, so I may have just been lucky.This stuff doesn't feel like typical PLA. It's got a "softer" feel to it, and will give organic prints an extra wow factor. The regular rock PLA has a very muted gradient that will make your prints pop, but not excessively. Looks extra nice for bones and skeleton models.My only complaint, and it is a minor one, is that it scratches very easily. Be very careful removing supports after a print, because scratches will leave behind very visible white scars. In my opinion, this material works best for display models.

I had a large print job (1.7 rolls) and the results were great... I took great care to make sure the rolls were dry because our house has humidity issues, but other than that I did nothing special... After about 46 hours of printing I switched to another roll to finish out the print job, and the color matched perfectly... You can't even tell where the transition is. There are a couple of layer lines that stick out a little where my cat ran across the printer, but I can hardly hardly blame the filament for that. Overture and Prusement filaments are both huge favorites of mine. I never seem to have to worry about either one of them as long as I treat them right. The navy blue matte is a very nice color as well.

Nice rough texture and looks great. Unfortunately the "goopyness" of it makes it very challenging to get first layer adhesion, and there will often be small imperfections across the print that are very minor but I don't have them with regular PLA. My filament is in the AMS full of fresh desiccant and has had time to dry, so that's not the issue.I will likely try a different rock PLA when this one runs out, as it gives me more problems than even ABS printing. But the look is worth it.

This filament doesn't need anything special, its cheap, its solid, and it just prints with no fuss. Made a few prints with this material and it never gave any issues, the diameter is consistent and the spooling never got stuck. One of my go to filaments.

I've used a lot of different manufactures of filiment and have never been let down by Overture in any of my printers. For a PLA product the Matte line prints great and is easy to clean up. I use an Ender 3, Bambu Labs X1Carbon, and a Bambu Labs A1 mini. This filiment works great in all three includeing the AMS and AMS lite from Bambu.

As someone who 3D prints A LOT... this filament has become my go to for several reasons. First, it looks really nice. The matte finish makes prints appear post processed before they are sanded. Second, the quality control is excellent, I have never received a bad filament after ordering hundreds of rolls. Third, it prints perfectly. One random thought is that I love the cardboard spools. The only negative I would say, and this is similar with all PLA filament, is that it readily absorbs moisture from the air and this will ruin print quality. Be sure to dry this filament before use if it sits out a long time in a humid climate.Overall, HIGHLY recommend this filament.

セール時にホワイト・シルクを購入しました。一見してわかるほど艶があるわけではないです。角度によっては安いホワイトABSに見えます。その代わり、かどうかは分かりませんが、シルクのフィラメントにしては安定性がよく、薄くてもボロボロにはなりません。普通のホワイトPLAと比べたら明らかにシルク感はあるので、ホワイトと組み合わせてアクセントをつけた造形はどうだろうかとアイデアを練っています。

Fast delivery and good quality materia gives excellent printing. Highly recommend.

I always go for overture filament, and it never disappoints, it always melts well and sticks to the plate well, will definitely be buying again.

I bought the matte white form of this filament to use making lithophanes. Overall it's a decent low-cost option, but it's pretty fragile and prone to slight delamination when working with thin layers. PLA+ filaments will definitely perform better, but the value for money on this filament is to me far superior

Good results at 200 degrees on the ankermaker m5