Proxicast Pro-Grade J-Max 100% Solid Stainless Steel Antenna Mount - Universal Outdoor Adjustable Pivot/Lock Bracket & J-Pipe Mast (1.5" x 36" Pole) for Wall, Eave or Roof Mounting (ANT-800-JP3-XL)

I have a new gen3 starlink dish. Its well known that up until May2024 that the starlink pipe adaptor is garbage. So I needed to improvise. Proxicast has been wildly popular with early generation starlink dishes. I have one of the OAM starlink wall mounts, but the extension pipe is MUCH MUCH to short. The advantage of the OAM wall mount is a very firm connection to the dish itself. So comes in the improvise. Use the proxicast J mount to provide the extension. a standard well made u-bolt pipe adaptor clamp, and the OAM stalink pole/mount. As show in one photo is all three together.install on a facia of a steep metal roof comes next week.Pros:- high quality material- all nuts and bolts included- clear install instructions- pipe diameter is perfect fit (with a couple wraps of duct tape to fit snug) with starlink pole mountCons:- with this kit, none- with proxicast in general, I wish they had a gen3 starlink pipe adaptor

I ordered this antenna mount to install an outdoor PoE mesh network access point for my Starlink service. I was looking for a sturdy mount that would hold to the weather. The Proxicast Pro-Grade J-Max 100% Solid Stainless Steel Antenna Mount more than filled the task. I chose the stainless steel mount over the aluminum since it was only a few dollars more. Also, I wanted to increase the height of the mast by adding additional tubing, so the stainless steel should be able to carry any extra weight easily.The mount was straightforward to install. After installing the base support to the wall, there are only 4 bolts to insert and tighten. However, a couple of the base's mounting holes are directly behind the J arm. If you want to use these, you may have to assemble the unit in place rather than on the ground. The two small bolts holding the arm have to be slid in from the inside to the J arm tube. It was tricky holding the bolt inside the tube to line it up with the provided hole while standing on a ladder.I have vinyl siding, so I wanted to use the facia board on the soffit. The base support is a bit large (over 7 inches) and my facia boards are not that wide. I wound up using a front corner that gave me more surface area. Since I wanted to add to the mast height by a few feet, I used 1-inch PVC schedule 40 pipe. That size was almost perfect and slid fairly snuggly into the Proxicast J arm. I inserted the PVC pipe to the bend in the J-arm and added a few feet of length. I used 2 additional 1/4-inch bolts to secure the pipe. All in all, a very solid installation.

I used this to mount a Ambient Weather station on the facia at the peak end of my roof.Using the provided holes I was able to get a solid mounting. I wasn't able to utilize the sloted holes for pluming the mast left or right due to there not being any good support at the center, but this was my builders fault. The other direction was easy to make ajustments and get plumb.I did chose to purchase stainless steel lag bolts as the provided bolts stuck to a magnet and appeared to be plated. My wife wasn't strongly in favor of the weather station and I didn't want to risk going to the doghouse because of a couple rust treaks in a few years. ;^)To get ideal wind information one should get height extensions that likely would require additional support, but in my case wind was only a minor consideration.Great product and stainless steel too.

This holds my Starlink receiver off a vertical porch support.Solid and sturdy the one problem I'm working on is locking in a small, 1 degree misalignment. This is partly the fault of the Starlink which does not have adjustment in its pole adapter.

The quality of the mast is great for the price. It worked great for my WeatherXM station. It mounted and was very stable and sturdy. It has been through a few storms and hasn’t moved an inch. It came with all the hardware needed to mount and get everything in place. I highly recommend if you need a great quality mast.

Used to mount a weather station on the house.Mounting bracket was very strong and sturdy with mounting hole options. Pole is very strong and a perfect length and angle. Instructions for installation were good. Well packaged on arrival. Came with wood mounting bolts. Had to buy brick anchors for my situation. Highly pleased with product.

The design of this mount is simple, well thought out, and very effective. I used it along with the Starlink pipe adapter to mount my new Starlink residential dish on my roof. I have many trees and found the many possible mounting arrangements of this design allowed me to install in a convenient location with a 100% unobstructed field, as tested with the Starlink app. The stainless steel is a stout gauge, already tested in two high winds since my install.