CHANCS TYD-50 Synchronous Motor Turn Table 110V AC 5-6RPM CCW Flush Shaft 5.5mm Small Gear Motor

The motor is well made, it was delivered promptly and was priced reasonably. I ordered this motor to replace a worn out motor that oscillates my Lasko floor fan. I actually have two Lasko floor fans and after two summer seasons of 24/7 operation, the sleeve bearing on both motors wore out (badly....egg shaped). It was a not so good design application on Lasko's part since I think a motor with a sealed ball bearing on the output shaft would have not failed so quickly. But.....Lasko sells these fans for under 100.00 so there are choices to made. With this in mind, I will periodically oil the oscillating motor's main shaft since the grease that is applied during manufacture is not sufficient. The remainder of the original motor's internal gears show no abnormal wear so I am not concerned with the replacement motor giving out as long as I apply a few drops of oil to the main shaft during the time it is running. Amazon sells quite a few of these type motors and it is very important that you inspect each one carefully to choose a replacement that matches the output shaft of the one you are replacing as close as possible. There are shafts that are round, shafts that are round with a tapped end hole, shafts with one flat, shafts with two flats, shafts with all the preceding types but of different lengths. The output shafts on these motors are hardened so modifications to them will be doable but difficult. I found it a better choice to find a motor whose shaft most closely duplicated my original and then modify the plastic lever that was attached to the end of the shaft. My original motor had two flats so that is the type I bought but the replacement motor's shaft was about .030 larger across the flats so I had to modify the plastic lever to have it slip onto the motor shaft. If you are a tinkerer it will be no big deal but your careful choice of the replacement motor type will keep your modifications down to a minimum. Unless of course, you are luckier than I was and are able to find an exact replacement. All in all, this motor saved my 100.00 fan for about 13.00 and my time. One last thing- my original motor was specified as 2-3 RPM and the replacement motor was 5-6 RPM. This turned out to be fine with me since I always thought that the original motor moved the fan back and forth painfully slowww.

Fit , worked, ccw needed. Restored an old store sign Thx

This is about as close as I could find for replacing the motor in a department 56 skating pond. I picked this because it was one of the few that lists a CCW rotation instead of random rotation direction. Modification was required to make it work. The shaft was too long so I had to cut it off using a Dremel tool with a cutoff wheel. I used a sharp xacto knife to cut the bottom off the pond. Then the rest is removable with screws. The motor is riveted on so those will need to be drilled out. To rivet the new motor in, use 4mm (5/32) rivets with a minimum grip of about 1/8”.

Worked ok.

We ordered the same motor but this one is a bit too big. Working on getting it to fit. Fingers crossed.

It was replaced to tower fan's oscillation motor but not exactly same with old one. The drive shaft and housing bracket are a little bit different between new and old one that I fix shaft slot and bracket holes. Finally, it was used and work properly.

Better torque than the average microwave turntable motor. Single direction motor (CCW only) was better for my application.

Motor is a little noisy.

Très bon produit conforme à mes attentes

古い電気ストーブの首振り用モータですので、代替品がなく探しておりました、ほぼ似たようなものがあり購入いたしました、中国製の為入手に2週間かかりましたが、商品は良品でした、外形寸法が少し大きかったので、ストーブの方を加工して使用しました、問題なく可動しております。

サーキュレータの首振りモータの修理に軸を少し細く加工して使用しました。回転数が少し早いですが問題無く動作中です。

6年間、仕事で使ってたサーキュレーターの横振りが壊れたので、修理用に購入しました。多少軸の形状が異なったので、削ったり接着したりが必要でしたが動作に問題無しでした。元のモーターの倍のスピードで首振りますが、それが良しですw

電子レンジのターンテーブルモーターが壊れたため、代替品を探索。同じ型番のものがないので、仕様がほぼ同一で、シャフトがDカットに近く、ストローク長がほぼ同じ本品を選択。問題なく取り付き、動作しました。これでまた電子レンジが使えます。助かりました。