brotect Screen Protector Anti-Glare compatible with DJI RC Controller (2 Pack) Screen Protector Matte, Anti-Fingerprint Protection Film

keeps the screen from scratches

Fits perfect. Brilliant.

Fits drone rc well

I fitted it as suggested in the bathroom and damp cleaned the surface areas around where I was going to work with a, damp microfiber cloth. I set everything up so there would be minimal disturbance of the air around the operating table before I commenced. I left the room for any airborne dust to settle. Bit elaborate I know but I have been down this road before but to disastrous ends because of not reading the instructions properly.The DJI mini 3 RC controller has a tempered glass protector fitted awhile ago. I thoroughly cleaned the screen with glasses wipes and went over it with a sticky dust lifter from another screen project. Its a pity they are not supplied with the matt screen as it is important to the success of the fitting I believe! Are you taking note Brotect?I applied it, LIGHTLY, in landscape orientation with the bottom edge laid first and at steep angle (nearly vertical) so as not to make too much contact with the screen until I was confident it was aligned with the edges too. I then slowly lowered it looking at the sides to see if they were parallel. As it was slowly lowered the screen slowly went to get black with no air bubbles to jump up and down about. I only had two tiny bubbles in one corner that were quickly removed with light massage with a soft cloth over a credit card - beautifully done by a novice with a bit of time and patience!I am very impressed with the result but had reservations putting it on another tempered glass protector, There is no impact on the touch screens sensitivity whatsoever.The photos were taken with the controller flat on the garden slabs looking at the sky with the tripod and camera directly overhead at 2ft above, you can just see a faint reflection.The wire looking mesh you see on the screen in the sky area is not visible in use to the eyes - its called Moray Patterning, check it out in a search engine. In that photo the gimble was at about 45 degrees towards the sky.Would I recommend it - yes most defiantly would.

Great product to combat glare on glossy screen on controller, it works and just needs careful placement, just slightly smaller than screen size

Great product and easy to fit

Poderia ser melhor

Seit vielen Jahren greife ich immer wieder zu Produkten von brotec. So auch für den neuen DJI RC2 Controller zum "brotect 2x Entspiegelungs-Schutzfolie kompatibel mit DJI RC Controller Matte Displayschutz-Folienset".Die Lieferung erfolgte schnell per Briefpost, alles kam sicher an. Die Montage geht spielend einfach und war in wenigen Sekunden erledigt. Wichtig: Vorher wirklich für einen fett- und staubfreien Bildschirm sorgen, sonst gibt es unschöne Blasen, die gerade bei matten Folien noch stärker sichtbarer sind.Wie ist die Bildqualität im Vergleich zum Originalzustand ohne die Folie? Anders, aber nicht schlechter. Sogar stellenweise sogar besser, wenn man draußen in hellen oder sehr hellen Umgebungen ist. Denn dann gibt es viel weniger Reflexionen, der Controller wird dank der Folie definitiv besser nutzbar.Er ist auch mit der Folie hell genug, Bilder sehen nach wie vor sehr gut aus und alle OSD-Anzeigen sind einwandfrei lesbar. Und das Wichtigste: Der Touchscreen funktioniert einwandfrei. Klar, Bilder erscheinen durch die Folie etwas matter und nicht mehr ganz so leuchtstark. Aber im Zweifel kann man sie mit der Folie besser ablesen als ohne die Folie. Deshalb eine klare Kaufempfehlung. Hochwertige Folie, passgenau geschnitten und einfache Anbringung. Schade nur, dass kein Reinigungsmaterial dabei liegt.

Het is ideaal en en schittert niet door de zon.

Ottimi filtri salvaschermo opachi, funziona bene l antiriflesso, comprati per ovviare a questo inconveniente sul display del controller del mini 3 pro, ottimo prodotto

Perfecto encaje en la pantalla y quita todos los reflejos. Lo recomiendo