DEEPCOOL MATREXX 30 SI Alloy Steel Mini Tower Computer Case/Gaming Cabinet - Black, Support - Micro ATX/Mini-ITX, Pre-Installed 1 x 120 mm Black Fan at Rear - DP-MATX-MATREXX30-SI

In short: Value for money. Sleek and aesthetic. Definitely go for it if you're on a budget.In details:The packaging was good. It came in its own DeepCool package and then one more layer of Amazon package.The temperatures are pretty good. It is around 40-50 for me. But I don't game so your mileage might vary.The looks are superb in this price point and very much build friendly.Pros:1. The tempered glass on the side and front adds to the aesthetics. It looks amazing!2. Comes with 3 ARGB fans (CF120) installed and an ARGB strip. So if you have a motherboard with ARGB headers, you can control the lights with your motherboard. Unfortunately I do not have such a motherboard so can't tell how it works. (P. S. In my pictures, I moved the preinstalled fans to the top and back. The front fans in my picture are not the preinstalled ones)3. The case and LED controller with some built-in effects including static colors, breathing effect, sliding and rainbow effects. I connected 7 things (6 fans and the LED strips) to it and worked without a hiccup.4. It has a bottom mounted PSU and a PSU shroud to put all your extra cables in.5. It has a hard drive cage with two slots which is compatible with both 3.5" and 2.5" drives. You also get two additional 2.5" slots beside the motherboard. The hard drive cage can be moved (although only about a cm or so)6. The cable cutouts are intelligently placed and I didn't have any problem routing the cables.7. Comes with a lot of zip ties to help you in cable management.8. Has about 23mm clearance at the back so you can shove a lot of cables there. You can even put fan hubs or led hubs at the back.9. Magnetic dust filter on the top10. The top fans can be slid sideways and has 3 parallel slots so that you can adjust them to you liking.11. The fan at the back also has 3 slots to install for adjustment.Cons:1. The first and foremost problem is the instruction manual. It's basically worthless. It just had a few diagrams with labels and that's it. The instructions are really unclear. It took me 15 minutes to figure out how to take off the front panel, and took me half an hour to connect the fans' led strips. If you do not have PC building experience you might run into problems.2. All the screws came in the same pouch. It'd really help if they had different screws in different pouches. Again, this would not be an issue if the instructions were clear. It's really difficult to tell which screw goes where unless you have some idea.3. The unit I received had one bent thumb screw slot on the side panel which caused the screw to sit in an angle on the glass and took real force to unscrew and I scratched my finger. It's also terrifying because you might break the glass if you put too much force. I'd have liked a window like system instead of the thumb screw business. Also, the glass has no border, so don't drop it. Be careful!!4. The front panel is on the top right. So you have to stretch your hands quite a bit to reach them. It also has only one USB 3.0 and 2 USB 2.0. I'd like if it were all USB3 to be honest, but in this price point, I'll let it pass.5. The PCI extension slots are non reusable. You have to break them up in order to use them and you can't put them back. Also, make sure you remove them before inserting the motherboard as you have to go back and forth to remove them.6. The dust filter at the bottom is not magnetic and you have to slide it out of the cage. Minor inconvenience.7. Having a glass front panel means you'd have a little drop in the airflow. Probably very negligible.8. I'd liked it if the LED controller had more effects. The built in ones are good. But very little in number. Not a problem if you have an ARGB motherboard.9. The drive installation is not toolless. You have to screw them in.Overall verdict: Go for this case if you are on a budget. Even if you're not on a budget this is a superb case. Although if you are a beginner, you might get a little bit of trouble, just a little. If you're stuck at a problem, feel free to contact me at aniketmail669@gmail.com

I bought this case around 2 years ago. So I'm writing this is after using it for some time. Now, as the title says, functionally it is 5 out of 5. Cable management provisions are great, the front mesh provides plenty of airflow, the side panel mounting mechanism is a lot better than most others, paint quality is good and overall it is visually a very stunning case. Honestly the only improvement I could suggest would be to add perforations to the PSU shroud to improve airflow to the GPU(the newer CH370 case has them).BUT... You have to realise that to make it fit this 2.5K price point Deepcool had to cut a lot of corners in terms of build quality. The plastics are cheap:- the front panel uses a push in mounting mechanism and already a couple of the plastic push in bits are broken. The front panel has also developed a small rattle as the fans ramp up. The whole case is made of thin sheet metal. Every single panel is flimsy enough that a firm push can bend them. And I swear the motherboard provides more support to the structure than the motherboard tray does. Spots of rust have started showing up at the corners and crevices of the case. Compared to this, my old Antec case is built like a tank; the metal and plastics on that one are still strong even after a decade.Honestly, if Deepcool would make this same case with thicker metal and stronger plastics and price it for a little bit more, I'd buy it in a heartbeat.

I've had the opportunity to use the DEEPCOOL MATREXX 55 MESH ADD-RGB 4F Mid-Tower Tempered Glass CPU case, and I'm genuinely impressed. This case not only looks stunning with its mesh front panel and tempered glass side panel, but it also fits comfortably within a budget. The added RGB lighting provides a decent touch of style that complements the overall design.I've used a full ATX board in this case without any issues, making it versatile and accommodating for larger components. The case's spacious interior and sturdy build further contribute to its practicality.Cons:One downside to consider is that the tempered glass side panel demands cautious treatment due to its fragile nature.

The product material and related cords' quality very good. It looks nice when the start switch continuously lights blue led around the switch. The product is very spacious.Also the cord management to the side of the cabinet done smoothly.

This is a compact and well designed micro ATX case that comes with a rear case fan (3 pin only, no PWM), cable management space (approx. 1.5 cms) with cutouts on the left hand side, facility to mount a single 2.5 inch and multiple 3.5 inch SATA drives, dust covers and ventilation grills on front panel and bottom panels and a single USB3.0 and USB2.0 port on the front. It covers the basics for a no frills build and we have the option of mounting a case fan up front (not included, bought separately) for intake in the front and exhaust at the back. Cutout for CPU power cable not provided. Cable management is ok, not bad and not great. Gamers, note that it can accommodate graphics card of length up to 25cm only. Anything longer than that will require the 2.5/3.5 inch bay to be cut and removedThe airflow is good, with silent operations and temperatures within acceptable range, for a basic build without separate GPU. With GPU your mileage may varyEdit: added a GTX1650 Super GPU. Installation was moderately easy. So far so goodThe only downside to this case is that there is minimal facility for cable routing and management. It doesn't affect airflow but is really messyEdit: would recommend deepcool matrexx SI 40 instead as it has better airflow, easier build capability and cleaner cable managementEdit: After 2 months of use can confidently say that this case has poor thermal performance. keeping the side of the case open leads to a temperature drop of 5-7 degree C. If you plan on running heavy loads this case is not advisable. reduced to 3 stars

The media could not be loaded.  It’s a pretty simple, standard case. Good quality and has everything you need for your entire build. Wires, fans, screws, etc. were in good condition. Highly recommend this case to anyone.

This case is very easy to work with and for its price I cant complain. It’s super lightweight and is esthetically pleasing, would recommend for someone looking for a budget build.

Used this for my very tight budget pc build. Great price for what it is. I saw a lot of reviews with broken parts, however, that was not the “case” for me (pun intended). I think for my next pc build (in the far future as I’m now broke) I will get a case with a usb-c header on the front case io, however, this will do perfect for me now. What I don’t like is the case fans being molex cables directly to power supply and not able to change fan speed (or turn off the) by being connected to motherboard, but I can just change these fans at a later date.

Otimo

The media could not be loaded.  Perfect