3S 4S 12V 5A Battery Active Equalizer BMS Balancer Lipo Li-ion LFP LiFePO4 Lithium Battery Balance Active Energy Transfer Equalization Module Faster Whole Group Capacitor Balancer PCB

Funciona muy bien

Works the way it should

Bought four, cheap, 200AH LiFePO4 cells and a Daly 200A Smart BMS from aliexpress. Had one cell that would hit High Volt Disconnect (HVD) (w/BMS set @3.65V/cell) while the others would only average <3.250-3.300. I cleaned, sanded, swabbed, terminals and switched cells around to no avail. The best I could achieve on differential voltages were always >0.150, oftentimes >0.250 when charging at 30-40 amps. A capacity test yielded about 135AH +/-. After installing this active equalizer the cell differential voltages are always <0.010 and are more often than not <0.003. I now have my BMS set at a HVD of 3.60V and easily achieved 175AH (after charging @ 25 to 30 amps) when I quit the test early.I paid almost as much for the BMS as I did for the cells (the cells were actually that cheap). My thinking was that I would upgrade the cells in the near future for my camp trailer. However, the cells arrived well after I sold the trailer. I bought a smaller (energy wise) truck camper and now have no reason to upgrade. I now plan my energy for 175AH and am quite happy with my cheap battery.

Could not be more mad..I let this run for about 4 days hooked up to my 20s 72v ebike battery. I have about 4 rows of cells that became pretty out of balance over time. Progress was looking good every few hours I'd check it and voltage was slowly equalizing from the top down.Came out this morning and my garage smelled off.. Checked the board and it was off and not powered anymore though plugged in.Checked the cells top down and it started to looked good 3.7v on the dot, the last two rows however 0 VOLTS!!! My 72v battery was outputting only 56 volts. It completely killed the last two rows..This tool seems like it has the potential to be awesome - however my was clearly damaged and destroyed my $500 battery.I DO NOT recommend this to anyone.. manually balance each row and take the slow long route unlike me.Genuinely hopes this review helps save someone else's battery 🙏

I read through the reviews. Some people were having trouble with this equalizer, most reported it to work very well. I'm in that camp. After connecting it up to a 4S2P Lipo that showed one of the packs in the battery was out of balance with the other packs by a fairly good margin. I connected up the equalizer and left it on for two days through mild charging and discharging from my solar panels. The cell packs all came up to with in .01 volt. I powered up some items to draw the batteries down and then recharge them. The cells on the battery that had the balance issue stayed within .03 volt of each other, and once recharged returned to .01 volt difference. Works like a champ.

Simple to install. Checked with my clamp meter and it would transfer up to 2 amps on my system.Though it balances more aggressively than a BMS, if batteries are way out of balance I recommend parallel balancing batteries first. I also recommend taping some barley paper over the exposed circuits to prevent short circuits.

I’ve been having trouble keeping a custom 140Ah 4S LiFePO4 battery properly balanced. I decided to give this a try and am SO glad I did. Of all the solutions I’ve tried, this one has finally achieved a perfect top balance with all cells at 3.6500 +/- 0.005. It balances at a higher current than most others I’ve used, so is particularly well suited for larger sized setups. It didn’t get hot while working, not even warm to the touch, which is another huge plus since it’s in a closed space in a warm environment. It was running at several amps for an entire day in 90F environment and wasn’t even slightly warm. As an added bonus, it has pads where you can solder on a switch to remotely turn balancing on/off. I use this to disable balancing when battery is not in use, but can flip it on when charging. If you wanted to get fancy, you could even hook up a simple relay to automatically have it turn on with charging and off at rest. At rest, background current draw seems minimal, but I wouldn’t leave it hooked up if storing a pack for several weeks. All around, a FANTASTIC device.

You can run these in addition to the BMS balancer and they are far far superior. These should be built into every BMS and the resistor type should be outlawed.