NuvoLighting SF77/193 4-Light Bathroom Vanity Light Bar, 24-Inches, 100 Watts/120 Volts (Polished Chrome)

Very nice and half the price of others I've seen with just as good quality, easy to install too.

Hello everyone! First, do not remove the protective film until the very last moment. Second, read the instructions carefully. Carefully remove the decorative caps from the electrical sockets, they are also the clamps for attaching the decorative front panel. Decide on the cable. Make all connections inside. Do not try to pull the wires out. Do not remove the electrical sockets from their positions in the base. The fasteners are very fragile and break, then it will be difficult to fix them. I personally made additional corners from a plastic board and a slot and secured them with GORILLA glue to the base of the medical cabinet, if you go this way, wait a day for the glue to dry. Glued tightly and there is no need to drill holes in the wall and spoil the tiles. I aligned the front panel flush with the surface of the mirrors. LED lamps 1680 lumens, which corresponds to 100 W of ordinary lamps. But in reality it consumes no more than 20 W. That for all five lamps approximately real electricity consumption of only 100 W. The thing is delicate, be careful with it, do not leave dents, once again do not remove the protective film until the very moment you screw in the lamps. If you do everything correctly, you will get a sea of ​​​​beauty and light. I mistakenly first bought a smaller size with 4 lamps, but the company returned my money minus the cost of sending it back. But that was my mistake. I bought a second time but already the right size 30 inches. And this time everything fit just perfectly.I think you will see everything you need in the photo. The only thing I can add is that my outlet has a switch on the wall. When I did the renovation in the bathroom, I foresaw this in advance, making an outlet that can be turned on and off as you usually turn the light on and off with a switch on the wall. The only thing is that I placed the outlet a little high. And everything is fine there.

Easy to install, good quality

On the positive side, I like the color of the brass, the overall look, and it's all straight and relatively strong metal.On the negative side ... it was quite difficult to take apart, and I'm very experienced with building things. The vanity light came to me completely closed up, and there was no obvious way to open it in order to wire it. I finally used a screwdriver to push in the grounding clips on all four sockets in order to release the backplate. Once I did that, realized that the four collars, that surround each socket, are a form of ... one-directional clamp that holds the front plate to the back plate, and are not easy to remove. This is how vanity lights are usually taken apart - by removing the collars first. The instructions gave no hint of this, and I couldn't have removed them from the front easily anyways.So in the end, this was the process I had to do to mount this light:1) Pry the grounding clips off of the back plate - look for little black tabs on the backplate, and push the smaller one with a screwdriver.2) Once open, remove the grounding clips entirely from each socket.3) Push each socket forward enough to the point where the brass cup reaches and falls off of the back of the socket.4) Replace the sockets in their original location and reattach the grounding clips.5) Wire the neutral and hot lines.6) Wire the ground to the backplate, and wire the ground line. This means a 3-prong plug, not 2-prong plug, for wiring this without a junction box. It's got a metal case, so it has to be grounded.7) Put back on the front plate, and the sockets to hold it back on. The screw that goes through the top of the front plate to the back plate seems not that necessary with sockets like these.Hope that helps - if you receive one like mine you're in for a little extra work at the front end to get to the wiring.

I havent installed on wall yet, but i put it all together and works perfect.I did not install it into a wall fixture, rather a Craft Light Plug with a switch for easy on/off, also purchased on amazon (amazon recommended it as a frequently bought together item); it has 2 exposed wires on one end.Full instructions that i wish would come with the light:To remove backplate from front plate, grip chrome bulb covers that would sit at bulb base and slightly twist or just pull; the covers will slide off exposing just the bare ceramic; once all 4 are removed, youll be able to remove front plate.For the plug, the plug wont match the instructions; the plug will have two white wires and the light has a white & black. If you look closely at the two white wires one is grooved and the other is smooth. The smooth one is your black wire, the grooved is white. Very important; your light wont work if you get it backwards.Pinch your two wires closely together and insert into orange wire crimper thingy; once your wires are fully inserted, firmly pinch your two wires at topto keep in place and keep twisty orange piece over and over until it stops or wires want to bend with it. Repeat for other set of wires. To test pull on wires to make sure they dont come out and are very firm and tight into crimper.Seperate your black wires from your white wires into seperate sides of box; you want to do this because if any copper wire inside your crimper is exposed and touches exposed wire from the opposite colored set, it could potentially start a fire, so just seperate them for 100% safety.Run your plug wire along the edge and have it coming out side of light.Take the green screw and screw it half way into spot marked ground wire. Take your ground wire thats attached to front plate and make a small hook on end of it. Hook the ground wire around the ground wire screw on light back plate, and screw in the screw the rest of way to tighten the wire firmly behind the screw.At this point, it is fully operational and you can test it by screwing in a bulb and making sure it works. Once verified, remove bulb, put the front plate into place the same way you removed it, remove the blue protective film on the chrome, and put light base pieces back in place. Once you remove film, be mindful of fingerprints. It will look identical to when you first opened box, just with a wire coming out the side and no longer has the blue film on it..Take the small silver screw and put into small screw hole on side of unit; this will help keep it secure so the front/back plate cant come apart unless you remove screw.Screw in your 4 bulbs; some of mine were a lil cock eyed so i unscrewed the bulb and adjusted the ceramic base a tad to align it correctly then put the bulb back in. Hang up, and enjoy!Another note; i plugged a remote sensor box in and plugged this light into it, then put velco on back of remote and attached it to front of vanity so i didnt have to reach go turn off/on, just a nice simple click of a button. The remote sensor plugs into a single outlet and has 2 plugs on it. This leaves one outlet with 2 plugs for the remote, and one normal outlet open for non remote functions. I got a surge protector and plugged my curling iron, hot iron etc into it and then used this for the other port on the remote sensor; so when i use the remote off button for my light, my curling iron etc all turn off and i eliminate fire danger that beauty causes lol

worked well and nice and bright!

Llego rapido y en muy buenas condiciones

Gives my bathroom a nice warm light

I got my product but it's dented ....I took pictures