K Tool International90002 Q Bond Ultra Strong Adhesive Kit for Garages, Repair Shops and, DIY, Repairs Hard Plastics/PVC/Metals, (2) Adhesive Bottles, (1) Plastic and (1) Metal Reinforcing Powders

This product arrived at the house without any damages. No leaks to the product of any kind. Everything was boxed up and brand new.A guy at work told me about this stuff. It works really well. He was telling me they had a hole in an oil pan from a bolt getting tightened down too much. They were able to fix the hole in the oil pan with the Q Bond. It held until the new pan arrived, which was around a week or so. After hearing that I knew I needed some. I'm constantly having stuff break and can barely fix it with Gorilla Glue or superglue.I had a belt buckle that was shipped to me and broken in transit. I got a refund on it so it was free. I figured I might as well try to fix it. The stud that goes in the belt hole was broken off. I used gray powder Q Bond to put the stud back on the belt buckle. As seen in the picture it is holding fine. That is a pretty big deal since that stud has a lot of force on it once placed in the belt hole.I had a piece of plastic break off my cup holder lid in the car. The lif would no longer stay closed since the piece of plastic was what locked it into place. I used this product to place the plastic piece back on. It held just fine and the lid now operates as it should. No other glue would give such a clean fix.Don't glue your fingers together! The liquid glue sets up quickly. I almost lost a finger to the buckle. Really though, I did have to pull it off pretty quick. It is faster setting than super glue. I will use more caution next time and shouldn't have any problems.I like the little box that everything comes in. I'm keeping it in there to keep it organized. Everything comes with two little thumbtacks to scuff up the surface before you work on it. A scuffed surface holds the powder better and allows you to get the liquid to it. With proper powder placement you will have a clean fix. Like I said before, like no other glue that I've tried provides this.The cowl on my F-150 has been messed up since the day I got it. The two pieces always wanted to separate and the driver side rise up. I could snap it back together but it wouldn't hold very long. I got tired of fooling with it. I put Q Bond down in between those two cowl pieces and now it is held together. I haven't had it come back apart since I did this.I've already recommended this to a lot of people. Especially when I see that someone is trying to fix something or has something broke. I will be keeping this stuff on hand from now on. I'm just surprised I hadn't heard of it until recently, especially since it works so well.

Where has this been my whole life. This stuff is great. I am the type of person who trust to do jobs correctly and not cobble stuff together with duct tape and super glue but in the real world that's not always feasible and in those scenarios this stuff just makes a WAY more permanent fix than standard super glue. The super glue that comes in the kit is just normal runny super glue but the powders are where the magic at. It's like the little brother of JB weld with a much faster cure time. I use a thick super glue on one side of what ever I'm glueing together and the powder on the other and stick them together just to get a initial bond then apply a little more powder then use the supplied tiny super glue to really strengthen the bond. Store it in the fridge if possible so that the glue doesn't harden up as well

The situation:The front cover of my treadmill came out during our last move. It is screwed to the body of the treadmill with 4 screws (2 front and 2 back). Four plastic pieces broke off from the cover at points at which the screws attach the cover to the treadmill. To glue the pieces back to the cover was not an easy job because there is too much stress on the joints when the treadmill vibrates (specially at higher speeds) or when the cover has to move (when you increase incline). I have joined several broken plastic pieces before and several products in the market can do simple jobs. However, this was very different and challenging.Remedy:I tried two products (one cheap and the expensive "Strongest" joint) to attach the broken pieces, but they were not strong enough to withstand the stress from operating the treadmill. It broke every time and the new cover was $200- something I was unwilling to pay. I had given up and was using duct tape to keep the cover on the motor. Coincidentally, I saw a YouTube video showing this product. I liked the fact that it came with a powder that can reinforce the weak spot, so I decided to give it a try.Process:I scrapped off all the old glue (very important) and cleaned the surface with rubbing alcohol and let it fully dry. In the first stage, I used just a few (4-5) glue drops to join the pieces, making sure that they are exactly where they are supposed to be. It works VERY fast, so you need to be ready with how the joint should look like before you start. Caution: The "glue" is sort of watery and does not join the surfaces till it is dry (which is fairly quick). So it may appear like that it is not working, but if you hold it for a minute or so, it is done. If it is a simple job, you are done now. You need to go through the second stage, only if you need to make it "bullet-proof" and aesthetics are not that important. I needed the added reinforcement so I went to the second stage, after waiting for about an hour. I poured the powder around the dried joint. The powder is very fine, so take your time. I used a fine brush to fully cover the joint area with the powder making sure that I do not create a high heap anywhere. Wear a nose mask, as strong fumes will come out at this time. One at a time, put the glue drops on top of the powder very carefully making sure that it fully penetrates the powder without moving it. Leave it in the open dry place for an hour or so and you are done.Caution:1. Work outside the house.2. Use gloves, if possible. Use recommended cleaners to get the stuff off your hands.3. Use nose mask and stay clear of the fumes that come out when pouring glue on the powder.Outcome:My treadmill is holding very well after more than three months of usage at all speeds and inclines. It appears that the cover will not break at those spots again.BTW, it is made in Republic of South Africa and I will highly recommend the product.

This stuff is amazing, I fixed a broken plastic bracket from a heater that holds the igniter and knob and takes a lot of stress and it’s probably stronger than it was when new, there was literally a large piece that was missing after it broke that I couldn’t find and I just put a little piece of plastic behind it and then filled it in and it actually turned to plastic and I sanded it down to the shape. 100% recommend and will buy again and probably always make sure I have some available.