ACANIIFor 2005-2011 Toyota Tacoma LED DRL Halo Ring Black Housing Projector Headlights Headlamps, Driver & Passenger

I installed these headlights on my 2010 Tacoma, and by taking my time with the wiring, it wasn’t too difficult. They turned out looking great. Here’s how I did the install:1. Gather all the black wires from the back of the new headlight and combine them into one connection. (I attached them to a male contact point.)2. Gather all the red and white wires from the new headlight and combine them into one connection. (Again, I used a male contact point.) These will eventually connect to the DRL (daytime running lights).3. Locate the DRL wiring on each side of the vehicle. You’ll find a green wire (ground) and a black/white wire (hot).4. Splice a connection into each wire so you can connect the grouped wires from the headlights. (I used a simple quick-connect with a female contact.)5. Connect all the black wires from the headlights to the black/white wire (hot).6. Connect all the red/white wires to the green wire (ground).7. Test all functions to ensure everything is working properly, then reassemble.Tools you’ll need:• Quick connect/quick splice wire terminals• Crimping ToolWhile it might appear to be overwhelming at first, it’s rather easier than it looks. The lights seem plenty bright for me, but I’ve only had them for a short time, so I can’t speak to any potential issues yet.

The original lights were fogged over so I bought these. Makes my truck look great. They fit really good. You need some basic wiring skills to connect the LEDs, comes with an installation guide but it’s generic. Overall very happy.

So twi things when purchasing these.1. These are manufactured by Spyder and model number is 5011916.2. Toyota tacoma 2010 running lights only have 2 conductors so its easy to install.So i called spyder there in pst zone. They were helpful and answered my questions. However you install it be sure you pair red and white together, and all black wires together -so you should have two groups of wires. You’re splicing cables from the running lights. On my vehicle i have green and white & blue. White blue was negative for me. I did switch around to find out.I used lever nuts and solder which all worked. If you want to test twist the conductors together and test on the car battery. Leds are 12v so you can test the headlights before fully installing them. I love the look and look bright but the LED are not that bright but do the job of running lights. They look the same from the pictures. I would buy from the seller cheaper than most from others out here on amazon. Don’t buy stock ones but these. Either from here or spyder. Hope it helped.

I had bought another cheap pair months ago and the light output was dismal and scattered.I popped these in after wiring all hots and grounds to the parking light wires, and turned them on. Ten times better light output !And they are adjustable. I still have to tweak the horizontal, but vertical is perfect. They don't blind everyone else and I can see in the morning at 3:30AM when I go to work. The high beams are astonishing ! Awesome upgrade and the halos and LEDs make them even better !

They made a 2010 Tacoma look like a much newer model. The lights look awesome. The basic installation is about the same difficulty as changing the headlines with any new housing on a Tacoma. Wiring up the LED's and halos is not difficult if you understand wiring, but it can take some time if you want to do a quality job.

Bought these as a Christmas gift for my husband & they fit perfectly! I was nervous about buying them since I couldn't physically see it in place before buying but they're perfect & I love the blacked out look, they match with the taillights we already had installed.

poor quality

Almost didn't buy due to the consistent comments about how hard they are to install. "Need to be an electrician", "Mechanic couldn't figure it out".I am NOT an electrician or a mechanic. Just use the keep it simple stupid principal.Buy some female and male disconnects as well as a pack of quick splice connectors. Not only will it make this a lot easier, vehicle will be pre-wired for future light changes or if you have to remove these for any reason (no cutting wires or removing tape later).Trim wires by about 6" and keep the trimmed pieces to use for pig tails. Connect all black wires together with one male connector and all other (white and red) wires together with another male connector, crimp and tape.Attach the thicker white and black trimmed wires to a female connector to create pig tail, crimp and tape.Connect a quick connecter to the green (hot) wire on the DTRL connecter with the white pigtail and one one the white (ground) wire with the black pigtail.Install the light as you normally would and then just connect the black connected wires to the black pigtail coming from the DTRL and the red and white connected wires to the white pigtail and you are done.You can pre-wire everything before you even take the old lights out.Really easy with this method. See pics.